![]() SM Hanson Music Rewards redeemed in-store will be surrendered at time of purchase. Where can I use my SM Hanson Music Rewards certificates? To redeem SM Hanson Music Rewards, you must come to our Retail store, go online to, or call 80 by the expiration date shown on the SM Hanson Music Rewards certificate. When did I start earning points towards SM Hanson Music Rewards? As of July 5, 2021, points began accruing towards rewards with purchases made In-Store or On-Line at SM Hanson Music. Additional points may be earned during periodic special promotions such as 2x points, determined at SM Hanson Music’s discretion. ![]() You will continue to earn Rewards certificates in $5 increments, for every $ 200.00 in purchases. Once you accumulate $200 in purchases - you will earn a $5 Rewards certificate, or 2.5% in Rewards. If returns and adjustments exceed purchases, this could result in negative reward points. How are rewards points calculated? You will earn points for every one dollar (less tax and shipping fees) spent. Where can I find the Terms & Conditions for the SM Hanson Music Rewards program? Full program Terms & Conditions can be found at /rewards. Is there a cost for membership in the program? The SM Hanson Music Rewards program is free.ĭo you require a credit card to participate? No - The SM Hanson Music Rewards program is available on Cash, Credit/Debit Card, Layaway and 3rd party finance. How do I join the SM Hanson Music Rewards program? The SM Hanson Music Rewards Program is automatically available In-Store and On-Line purchases. SM Hanson Music Rewards Program Frequently Asked Questions and Program Terms: See below for full terms and conditions.Reward Members must have an valid/active email address to participate in the program.Use your certificates within 365 days to get the gear you want.Receive $5 in Rewards for every $ 200.00 spent on new purchases.Earn points for every dollar (less tax and shipping fees) spent on in-store or online purchases.The ToneWoodAmp is now securely attached to the guitar using the magnetic X-brace and the suction tape. Remove the blue tape used to secure the ToneWoodAmp to the back of the guitar. It is now securely adhered to the inside of the guitar.Ĥ. After resting the magnets in place and checking with your fingers that all four points of the magnetic X-brace is aligned and magnetically attracted, press down on the magnetic X-brace firmly. Some touches can happen but do not press down on the stickers until the magnetic X-brace is in position.ģ. Repeat the steps 3–8 from the practice dry run to place the X-brace but avoid touching the white sticky pads to the wood until you feel your magnetic destination again. Remove the thin protective liners from the white double-sided adhesive stickers on the X-brace magnets, leaving the white sticky pads on the magnets.įour extra stickers are provided in the ToneWoodAmp packaging in case you make a mistake.Ģ. *It is important to make sure the inside of your guitar is free of dust or debris before attaching the stickers*ġ. To install the magnetic X-brace in its proper position: Make sure that no brace, end-pin, or cables are in the way, and remove the magnetic X-brace from the guitar. You should feel the same resistance from each magnet before detaching.Ĩ. Test that all four magnets attract to the ToneWoodAmp by trying to lift each magnet on the brace. Allow the two back magnets to rest on the wood first, then let the other front two magnets fall into place.ħ. Move the magnetic X-brace towards the rear of the guitar until you feel the magnetic attraction between the lower magnets and the ToneWoodAmp on the other side.Ħ. Hold the magnetic X-brace at a 45° angle with the back magnets closer to the guitar’s back.ĥ. Insert the magnetic X-brace into the guitar body through the sound hole.Ĥ. NOTE: Do not yet remove the protective liners on the adhesive stickers of the magnetic X-brace!ģ. Loosen your strings so there is no tension. With the ToneWoodAmp still adhered to the back of your acoustic guitar with the two strips of 3M tape set the guitar top side up on a sturdy, soft surface.Ģ. To practice a dry run installing the magnetic X-brace:ġ. ![]() The second phase is actually installing the X-brace. ![]() We describe how to install the X-brace in two phases: First is a practice run so you can explore and understand the internal structure of the guitar before installing the X-brace. It uses double-sided 3M tape to adhere to the inside of the guitar’s body and secure the ToneWoodAmp to your guitar with strong magnets. The magnetic X-brace lets you attach the ToneWoodAmp securely to your guitar. ToneWoodAmp Artist Jake Allen - Like and follow Jake Allen on Facebook!
0 Comments
Leave a Reply. |